Electronic Components Datasheet Search |
|
LM77CIMM-3 Datasheet(PDF) 11 Page - Texas Instruments |
|
LM77CIMM-3 Datasheet(HTML) 11 Page - Texas Instruments |
11 / 23 page LM77 www.ti.com SNIS103F – JUNE 1999 – REVISED MARCH 2013 Reading the LM77 can take place either of two ways: If the location latched in the Pointer is correct (most of the time it is expected that the Pointer will point to the Temperature register because it will be the data most frequently read from the LM77), then the read can simply consist of an address byte, followed by retrieving the corresponding number of data bytes. If the Pointer needs to be set, then an address byte, pointer byte, repeat start, and another address byte plus required number of data bytes will accomplish a read. The first data byte is the most significant byte with most significant bit first, permitting only as much data as necessary to be read to determine the temperature condition. For instance, if the first four bits of the temperature data indicates a critical condition, the host processor could immediately take action to remedy the excessive temperature. At the end of a read, the LM77 can accept either Acknowledge or No Acknowledge from the Master (No Acknowledge is typically used as a signal for the slave that the Master has read its last byte). An inadvertent 8-bit read from a 16-bit register, with the D7 bit low, can cause the LM77 to stop in a state where the SDA line is held low as shown in Figure 9. This can prevent any further bus communication until at least 9 additional clock cycles have occurred. Alternatively, the master can issue clock cycles until SDA goes high, at which time issuing a “Stop” condition will reset the LM77. Figure 9. Inadvertent 8-Bit Read from 16-Bit Register where D7 is Zero (“0”) (Selects which registers will be read from or written to): Table 1. POINTER REGISTER P7 P6 P5 P4 P3 P2 P1 P0 0 0 0 0 0 Register Select P0–P2: Register Select: P2 P1 P0 Register 0 0 0 Temperature (Read only) (Power-up default) 0 0 1 Configuration (Read/Write) 0 1 0 THYST (Read/Write) 0 1 1 T_CRIT (Read/Write) 1 0 0 TLOW (Read/Write) 1 0 1 THIGH (Read/Write) P3–P7: Must be kept zero. Table 2. TEMPERATURE REGISTER (Read Only): D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 Sign Sign Sign Sign MSB Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 CRIT HIGH LOW Status Bits D0–D2: Status Bits D3–D15: Temperature Data. One LSB = 0.5°C. Two's complement format. Table 3. CONFIGURATION REGISTER (Read/Write): D7 D6 D5 D4 D3 D2 D1 D0 0 0 0 Fault Queue INT Polarity T_CRIT_A INT Mode Shutdown Polarity Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 11 Product Folder Links: LM77 |
Similar Part No. - LM77CIMM-3 |
|
Similar Description - LM77CIMM-3 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |