 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
MCP2510-ISO Datasheet(PDF) 52 Page - Microchip Technology |
|
||||||||||||||||||||||||||||||
MCP2510-ISO Datasheet(HTML) 52 Page - Microchip Technology |
|
|
52 / 80 page  MCP2510 DS21291F-page 52 © 2007 Microchip Technology Inc. counters are reset and deactivated in this state. The lis- ten-only mode is activated by setting the mode request bits in the CANCTRL register. 9.4 Loopback Mode This mode will allow internal transmission of messages from the transmit buffers to the receive buffers without actually transmitting messages on the CAN bus. This mode can be used in system development and testing. In this mode the ACK bit is ignored and the device will allow incoming messages from itself just as if they were coming from another node. The loopback mode is a silent mode, meaning no messages will be transmitted while in this state, including error flags or acknowledge signals. The TXCAN pin will be in a reccessive state while the device is in this mode. The filters and masks can be used to allow only particular messages to be loaded into the receive registers. The masks can be set to all zeros to provide a mode that accepts all mes- sages. The loopback mode is activated by setting the mode request bits in the CANCTRL register. 9.5 Normal Mode This is the standard operating mode of the MCP2510. In this mode the device actively monitors all bus mes- sages and generates acknowledge bits, error frames, etc. This is also the only mode in which the MCP2510 will transmit messages over the CAN bus. REGISTER 9-1: CANCTRL - CAN CONTROL REGISTER (ADDRESS: XFh) R/W-1 R/W-1 R/W-1 R/W-0 U-0 R/W-1 R/W-1 R/W-1 REQOP2 REQOP1 REQOP0 ABAT — CLKEN CLKPRE1 CLKPRE0 bit 7 bit 0 bit 7-5 REQOP<2:0>: Request Operation Mode 000 = Set Normal Operation Mode 001 = Set Sleep Mode 010 = Set Loopback Mode 011 = Set Listen Only Mode 100 = Set Configuration Mode All other values for REQOP bits are invalid and should not be used Note: On power up, REQOP = b’111’ bit 4 ABAT: Abort All Pending Transmissions 1 = Request abort of all pending transmit buffers 0 = Terminate request to abort all transmissions bit 3 Unimplemented: Read as '0' bit 2 CLKEN: CLKOUT Pin Enable 1 = CLKOUT pin enabled 0 = CLKOUT pin disabled (Pin is in high impedance state) bit 1-0 CLKPRE <1:0>: CLKOUT Pin Prescaler 00 =FCLKOUT = System Clock/1 01 =FCLKOUT = System Clock/2 10 =FCLKOUT = System Clock/4 11 =FCLKOUT = System Clock/8 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ’1’ = Bit is set ’0’ = Bit is cleared x = Bit is unknown |
Similar Part No. - MCP2510-ISO |
|
Similar Description - MCP2510-ISO |
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.NET |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
allmanual.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
