Electronic Components Datasheet Search |
|
19226 Datasheet(PDF) 3 Page - List of Unclassifed Manufacturers |
|
19226 Datasheet(HTML) 3 Page - List of Unclassifed Manufacturers |
3 / 4 page Included with each Multi-Mount Continuous Monitor should be: 1 Multi-Mount Monitor 1 24VAC Power Adapter (120V for 19226, 220V for 19227) 1 6' Mat Monitor Cord (Black) 1 6' Mat Ground Cord (Green and Yellow) 2 Push and Clinch Snaps 2 Mounting screws 2 Counter Sink Washers 1 Set of hook and loop fasteners 1 Certificate of Calibration I. A convenient 120VAC or 220VAC outlet should be located and tested for proper wiring and grounding. We recommend Desco Item 98130 AC Outlet Analyzer to verify proper wiring and ground. II. The Multi-Mount Continuous Monitor may be mounted to a convenient location using the included mounting screws or Velcro® set. See Figure 3 for installation set-up. III. Install Screws and Washers or Push and Clinch snaps 12 to 72 inches apart from each other on the work surface mat. Make sure that they pierce and clinch the bottom side of the mat. (See Figure 3). IV.Route the black ground cord to the monitor’s green terminal block labeled MAT. V. Route the green ground cord to the monitor’s green terminal block labeled GND. VI.Connect the power adapter to the monitor’s power jack labeled “24VAC” and the other end to a proper voltage source. TB-3028 Page 3 of 4 Operation When the Multi-Mount Continuous Monitor is installed to an ESD protective work surface and grounded via a power cord, the green WORKSURFACE GROUND LED and red OPERATOR GROUND LED should be illuminated. The monitor takes 6 seconds to activate its alarm circuitry when it is first plugged in. • The work surface resistance is measured between the two cords installed to the mat worksurface (See Figure 3). TO USE THE CONTINUOUS MONITOR: 1. Plug a wrist strap cord, not attached to the wristband, into the monitored banana jack labeled OPR on the side of the unit (See Figure 2). This automatically activates the selected operator channel. The red operator LED should illuminate. 2. Remove the charges from your body by making contact with a properly grounded ESD worksurface. Snap the cord to the wristband, and fit it snugly onto your wrist. This should silence the audible alarm and cause the OPERATOR GROUND LED to switch from red to green. If this does not happen, examine the wrist cord for continuity or damage and your wrist band to ensure that it is securely fit. If you have dry skin, apply an approved dissipative hand lotion such as Desco Reztore™ ESD Hand Lotion. When leaving the area, the user can take the wrist cord along or attach it to the monitor parking snap. The audible alarm will shut off in approximately 6-8 seconds when operator wrist cord is removed from unit and will instantly shut off when the cord is attached to the parking snap. NOTE: It is recommended that you use the Parking Snap rather than continuously removing the Banana Plug from its jack. PARKING SNAP The audible alarm is designed to alert both the operator and supervisor. The parking snap feature allows the operator to disconnect when leaving the work area without sounding the audible alarm. It also provides a means for wrist cord storage (red OPERATOR GROUND LED will illuminate). When the operator touches the parking snap, the audible alarm will disable for 6 seconds. The user can then disconnect the wrist cord from the wrist band and attach it to the parking snap for storage. If the operator removes the wrist cord plug from the OPR banana jack, the audible alarm will sound for 6-8 seconds. © 2011 DESCO INDUSTRIES INC. Employee Owned DESCO WEST - 3651 Walnut Avenue, Chino, CA 91710 • (909) 627-8178 • Fax (909) 627-7449 DESCO EAST - One Colgate Way, Canton, MA 02021-1407 • (781) 821-8370 • Fax (781) 575-0172 • Web Site: Desco.com Figure 3. Installation method #1 of the Multi-Mount Continuous Monitor Screw allows ground cord to be bolted to mat; keeps cord from disconnecting. or 10mm snaps need to pierce and clinch bottom side of mat. Snaps need to be 12 to 72 inches apart Work Surface Mat Power Adapter Connection Figure 4. Installation method #2 of the Multi-Mount Continuous Monitor |
Similar Part No. - 19226 |
|
Similar Description - 19226 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |