Electronic Components Datasheet Search |
|
ADS7810U Datasheet(PDF) 7 Page - Burr-Brown (TI) |
|
|
ADS7810U Datasheet(HTML) 7 Page - Burr-Brown (TI) |
7 / 11 page ® ADS7810 7 STARTING A CONVERSION The combination of CS (pin 24) and R/C (pin 23) LOW for a minimum of 40ns puts the sample/hold of the ADS7810 in the hold state and starts a conversion. BUSY (pin 25) will go LOW and stay LOW until the conversion is completed and the internal output register has been updated. All new convert commands during BUSY LOW will be ignored. The ADS7810 will begin tracking the input signal at the end of the conversion. Allowing 1.25 µs between convert com- mands assures accurate acquisition of a new signal. Refer to Table I for a summary of CS, R/C, and BUSY states and Figures 2 and 3 for timing parameters. CS and R/C are internally OR’d and level triggered. There is not a requirement which input goes LOW first when initiating a conversion. If it is critical that CS or R/C initiate the conversion, be sure the less critical input is LOW at least 10ns prior to the initiating input. CS R/C BUSY OPERATION 1 X X None. Databus in Hi-Z state. ↓ 0 1 Initiates conversion. Databus remains in Hi-Z state. 0 ↓ 1 Initiates conversion. Databus enters Hi-Z state. 01 ↑ Conversion completed. Valid data from the most recent conversion on the databus. ↓ 1 1 Enables databus with valid data from the most recent conversion. ↓ 1 0 Conversion in progress. Databus in Hi-Z state, enabled when the conversion is completed 0 ↑ 0 Conversion in progress. Databus in Hi-Z state, enabled when the conversion is completed 00 ↑ Conversion completed. Valid data from the most recent conversion in the output register, but output pins D11-D0 are tri-stated. X X 0 New convert commands ignored. Conversion in progress. BASIC OPERATION Figure 1 shows a basic circuit to operate the ADS7810. Taking R/C (pin 23) LOW for a minimum of 40ns will initiate a conversion. BUSY (pin 25) will go LOW and stay LOW until the conversion is completed and the output registers are updated. Data will be output in Binary Two’s Complement with the MSB on D11 (pin 6). BUSY going HIGH can be used to latch the data. All convert commands will be ignored while BUSY is LOW. The ADS7810 will begin tracking the input signal at the end of the conversion. Allowing 1.25 µs between convert com- mands assures accurate acquisition of a new signal. Table I. Control Line Functions for ‘read’ and ‘convert’. FIGURE 1. Basic Operation DESCRIPTION ANALOG VALUE DIGITAL OUTPUT Full Scale Range ±10V Least Significant 4.88mV Bit (LSB) BINARY CODE HEX CODE +Full Scale 9.995V 0111 1111 1111 7FF (10V – 1LSB) Midscale 0V 0000 0000 0000 000 One LSB below –4.88mV 1111 1111 1111 FFF Midscale –Full Scale –10V 1000 0000 0000 800 BINARY TWO'S COMPLEMENT TABLE II. Ideal Input Voltages and Output Codes. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 27 26 25 24 23 22 21 20 19 18 17 16 15 ADS7810 50 Ω ±10V –5V +5V 0.1µF NC 10µF + + + 0.1µF 10µF Convert Pulse BUSY 40ns min D0 (LSB) D1 D2 D3 D6 D5 D4 D7 D8 D9 D10 D11 (MSB) 0.1µF 10µF + + |
Similar Part No. - ADS7810U |
|
Similar Description - ADS7810U |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |