 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
IDT72264L15TF Datasheet(PDF) 8 Page - Integrated Device Technology |
|
||||||||||||||||||||||||||||||
IDT72264L15TF Datasheet(HTML) 8 Page - Integrated Device Technology |
|
|
8 / 31 page  8 IDT72264/72274 VARIABLE WIDTH SUPERSYNC FIFO ™ (8192 x 18 or 16384 x 9) and (16384 x 18 or 32768 x 9) COMMERCIAL TEMPERATURE RANGES operate in IDT Standard mode or First Word Fall Through (FWFT) mode. If, at the time of Master Reset, FWFT/SI is LOW, then IDT Standard mode will be selected. This mode uses the Empty Flag ( EF) to indicate whether or not there are any words present in the FIFO memory. It also uses the Full Flag function ( FF) to indicate whether or not the FIFO memory has any free space for writing. In IDT Standard mode, every word read from the FIFO, including the first, must be requested using the Read Enable ( REN) line. If, at the time of Master Reset, FWFT/SI is HIGH, then FWFT mode will be selected. This mode uses Output Ready ( OR) to indicate whether or not there is valid data at the data outputs (Qn). It also uses Input Ready ( IR) to indicate whether or not the FIFO memory has any free space for writing. In the FWFT mode, the first word written to an empty FIFO goes directly to Qn, no read request necessary. Subsequent words must be accessed using the Read Enable ( REN) line. After Master Reset, FWFT/SI acts as a serial input for loading PAE and PAF offsets into the programmable registers. The serial input function can only be used when the serial loading method has been selected during Master Reset. FWFT/SI functions the same way in both IDT Standard and FWFT modes. WRITE CLOCK (WCLK) A write cycle is initiated on the rising edge of the WCLK input. Data set-up and hold times must be met with respect to the LOW-to-HIGH transition of the WCLK. The write and read clocks can either be asynchronous or coincident. WRITE ENABLE ( WEN WEN) When the WEN input is LOW, data can be loaded into the input register on the rising edge of every WCLK cycle. Data is stored in the RAM array sequentially and independently of any on-going read operation. When WEN is HIGH, the input register holds the previous data and no new data is loaded into the FIFO. To prevent data overflow in the IDT Standard Mode, FF will go LOW , inhibiting further write operations. Upon the comple- tion of a valid read cycle, FF will go HIGH allowing a write to occur. WEN is ignored when the FIFO is full. To prevent data overflow in the FWFT mode, IR will go HIGH, inhibiting further write operations. Upon the completion of a valid read cycle, IR will go LOW allowing a write to occur. WEN is ignored when the FIFO is full. READ CLOCK (RCLK) Data can be read on the outputs, on the rising edge of the RCLK input, when Output Enable ( OE) is set LOW. The write and read clocks can be asynchronous or coincident. READ ENABLE ( REN REN) When Read Enable is LOW, data is loaded from the RAM array into the output register on the rising edge of the RCLK. Regarding FF: Note that since no more than Full - 2 writes are allowed between a Reset and a Retransmit Setup, FF will remain HIGH throughout the setup procedure. For IDT Standard mode, updating the PAE, HF, and PAF flags begins with the "first" REN-enabled rising RCLK edge following the end of Retransmit Setup (the point at which EF goes HIGH). This same RCLK rising edge is used to access the "first" memory location. HF is updated on the first RCLK rising edge. PAE is updated after two more rising RCLK edges. PAF is updated after the "first" rising RCLK edge, followed by the next two rising WCLK edges. (If the tskew2 specification is not met, add one more WCLK cycle.) If FWFT mode is selected, the FIFO will mark the beginning of the Retransmit Setup by setting OR HIGH. The change in level will only be noticeable if OR was LOW before setup. During this period, the internal read pointer is set to the first location of the RAM array. When OR goes LOW, Retransmit Setup is complete; at the same time, the contents of the first location are automatically displayed on the outputs. Since FWFT Mode is selected, the first word appears on the outputs, no read request necessary. Reading all subsequent words requires a LOW on REN to enable the rising edge of RCLK. Writing operations can begin after one of two conditions have been met: OR is LOW or 14 cycles of the faster clock (RCLK or WCLK) have elapsed since the RCLK rising edge enabled by the RT pulse. The assertion time of OR during Retransmit Setup is variable. The parameter tRTF2, which is measured from the rising RCLK edge enabled by RT to the falling edge of OR is described by the following equation: tRTF2 max. = 14*Tf + 4*TRCLK (in ns) where Tf is either the RCLK or the WCLK period, whichever is shorter, and TRCLK is the RCLK period. Note that a Retransmit Setup in FWFT mode requires one more RCLK cycle than in IDT Standard mode. Regarding IR: Note that since no more than Full - 2 writes are allowed between a Reset and a Retransmit Setup, IR will remain LOW throughout the setup procedure. For FWFT mode, updating the PAE, HF, and PAF flags begins with the "last" rising edge of RCLK before the end of Retransmit Setup. This is the same edge that asserts OR and automatically accesses the first memory location. Note that, in this case, REN is not required to initiate flag updating. HF is updated on the "last" RCLK rising edge. PAE is updated after two more rising RCLK edges. PAF is updated after the "last" rising RCLK edge, followed by the next two rising WCLK edges. (If the tSKEW2 specification is not met, add one more WCLK cycle.) RT is synchronized to RCLK. The Retransmit operation is useful in the event of a transmission error on a network, since it allows a data packet to be resent. FIRST WORD FALL THROUGH/SERIAL IN (FWFT/SI) This is a dual purpose pin. During Master Reset, the state of the FWFT/SI input helps determine whether the device will |
Similar Part No. - IDT72264L15TF |
|
Similar Description - IDT72264L15TF |
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.NET |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
