Electronic Components Datasheet Search |
|
N87L42 Datasheet(PDF) 9 Page - Intel Corporation |
|
N87L42 Datasheet(HTML) 9 Page - Intel Corporation |
9 / 25 page UPI-C42UPI-L42 This circuitry gives the host direct control of port 2 bit 1 (P21) without intervention by the internal CPU When this opcode is executed P21 becomes a ded- icated output pin The status of this pin is read-able but can only be altered through a valid ‘‘D1’’ com- mand sequence (see Table 1) SUSPEND Invoke Suspend Power Down Mode OPCODE 1000 0010 (82h) or 1110 0010 (E2h) Enables device to enter micro power mode In this mode the external oscillator is off CPU operation is stopped and the Port pins are tristated This mode can only be exited via a RESET signal PROGRAMMING AND VERIFYING THE UPI-C42 The UPI-C42 programming will differ from the NMOS device in three ways First the C42 will have a 4K user programmable array The UPI-C42 will also be programmed using the Intel Quick-Pulse Program- ming Algorithm Finally port 2 bit three (P23) will be used during program as the extra address pin re- quired to program the upper 2K bank of additional memory None of these differences have any effect on the full CHMOS to NMOS device compatibility The extra memory is fully transparent to the user who does not need or want to use the extra memo- ry space of the UPI-C42 In brief the programming process consists of acti- vating the program mode applying an address latching the address applying data and applying a programming pulse Each word is programmed com- pletely before moving on to the next and is followed by a verification step The following is a list of the pins used for programming and a description of their functions Pin Function XTAL 2 Clock Input Reset Initialization and Address Latching Test 0 Selection of Program or Verify Mode EA Activation of ProgramVerify Signature RowSecurity Bit Modes BUS Address and Data Input Data Output During Verify P20–23 Address Input VDD Programming Power Supply PROG Program Pulse Input WARNING An attempt to program a missocketed UPI-C42 will result in severe damage to the part An indication of a properly socketed part is the appearance of the SYNC clock output The lack of this clock may be used to disable the program- mer The ProgramVerify sequence is 1 Insert 87C42 in programming socket 2 CS e 5V VCC e 5V VDD e 5V RESET e 0V A0 e 0V TEST 0 e 5V clock applied or inter- nal oscillator operating BUS floating PROG e 5V 3 TEST 0 e 0V (select program mode) 4 EA e 1275V (active program mode) 5 VCC e 625V (programming supply) 6 VDD e 1275V (programming power) 7 Address applied to BUS and P20–23 8 RESET e 5V (latch address) 9 Data applied to BUS 10 PROG e 5V followed by one 100 ms pulse to 0V 11 TEST 0 e 5V (verify mode) 12 Read and verify data on BUS 13 TEST 0 e 0V 14 RESET e 0V and repeat from step 6 15 Programmer should be at conditions of step 1 when the 87C42 is removed from socket Please follow the Quick-Pulse Programming flow chart for proper programming procedure shown in Figure 6 9 |
Similar Part No. - N87L42 |
|
Similar Description - N87L42 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |