Electronic Components Datasheet Search |
|
RH1056 Datasheet(PDF) 2 Page - Linear Technology |
|
RH1056 Datasheet(HTML) 2 Page - Linear Technology |
2 / 2 page DICE/DWF SPECIFICATION 2 RH1056 Linear Technology Corporation 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com LINEAR TECHNOLOGY CORPORATION 2006 LT 0606 • PRINTED IN USA Wafer level testing is performed per the indicated specifications for dice. Considerable differences in performance can often be observed for dice versus packaged units due to the influences of packaging and assembly on certain devices and/or parameters. Please consult factory for more information on dice performance and lot qualifications via lot sampling test procedures. Dice data sheet subject to change. Please consult factory for current revision in production. I.D.No. 66-13-1056 Note 1: Dice are probe tested at 25°C to the limits shown. Final specs, after assembly cannot be guaranteed at the die level due to yield loss and assembly shifts. For absolute maximum ratrings, typical specifications, performance curves and finished product specifications, please refer to the standard product data sheet. Note 2: For dice tested to tighter limits than those listed above and/or, lot qualification based on sample lot assembly and testing, please contact LTC Marketing. Note 3: VS = ±15V, TA = 25°C, VCM = 0V, unless otherwise noted. Note 4: This is not a reflection of actual IOS and IB. Typical values are 5pA and 20pA respectively at final test. JFETs sensitivity to light at wafer sort requires a loose limit. Note 5: Tested at a gain of “5”. SYMBOL PARAMETER CONDITIONS MIN MAX UNITS VOUT Output Voltage Swing RL = 2k, VS = ±15V ±12 V CMRR Common Mode Rejection Ratio VCM = ±11V, VS = ±15V 86 dB PSRR Power Supply Rejection Ratio VS = ±10V to ±18V 88 dB SR Slew Rate (Note 5) 10 V/μs IS Supply Current 6 mA DICE ELECTRICAL TEST LIMITS (Note 3) Rad Hard die require special handling as compared to standard IC chips. Rad Hard die are susceptible to surface damage because there is no silicon nitride passivation as on standard die. Silicon nitride protects the die surface from scratches by its hard and dense properties. The passivation on Rad Hard die is silicon dioxide that is much “softer” than silicon nitride. LTC recommends that die handling be performed with extreme care so as to protect the die surface from scratches. If the need arises to move the die around from the chip tray, use a Teflon-tipped vacuum wand. This wand can be made by pushing a small diameter Teflon tubing onto the tip of a steel-tipped wand. The inside diameter of the Teflon tip should match the die size for efficient pickup. The tip of the Teflon should be cut square and flat to ensure good vacuum to die surface. Ensure the Teflon tip remains clean from debris by inspecting under stereoscope. During die attach, care must be exercised to ensure no tweezers touch the top of the die. |
Similar Part No. - RH1056_15 |
|
Similar Description - RH1056_15 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |