 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
TS1005IG5T Datasheet(PDF) 8 Page - Silicon Laboratories |
|
||||||||||||||||||||||||||||||
TS1005IG5T Datasheet(HTML) 8 Page - Silicon Laboratories |
|
|
8 / 13 page  TS1005 Page 8 TS1005 Rev. 1.0 applications, oxygen sensors are used to detect the absence of oxygen; for example, vacuum-packaging of food products is one example. The circuit in Figure 1 illustrates a typical implementation used to amplify the output of an oxygen detector. The TS1005 makes an excellent choice for this application as it only draws 1.3µA of supply current and operates on supply voltages down to 0.8V. With the components shown in the figure, the circuit consumes less than 1.4 μA of supply current ensuring that small form-factor single- or button-cell batteries (exhibiting low mAh charge ratings) could last beyond the operating life of the oxygen sensor. The precision specifications of the TS1005, such as its low offset voltage, low TCVOS, low input bias current, high CMRR, and high PSRR are other factors which make the TS1005 an excellent choice for this application. Since oxygen sensors typically exhibit an operating life of one to two years, an oxygen sensor amplifier built around a TS1005 can operate from a conventionally-available single 1.5-V alkaline AA battery for over 145 years! At such low power consumption from a single cell, the oxygen sensor could be replaced over 75 times before the battery requires replacing! MicroWatt, Buffered Single-pole Low-Pass Filters When receiving low-level signals, limiting the bandwidth of the incoming signals into the system is often required. As shown in Figure 2, the simplest way to achieve this objective is to use an RC filter at the noninverting terminal of the TS1005. If additional attenuation is needed, a two-pole Sallen-Key filter can be used to provide the additional attenuation as shown in Figure 3. For best results, the filter’s cutoff frequency should be 8 to 10 times lower than the TS1005’s crossover frequency. Additional operational amplifier phase margin shift can be avoided if the amplifier bandwidth-to-signal bandwidth ratio is greater than 8. The design equations for the 2-pole Sallen-Key low- pass filter are given below with component values selected to set a 2kHz low-pass filter cutoff frequency: R1 = R2 = R = 1M Ω C1 = C2 = C = 80pF Q = Filter Peaking Factor = 1 f–3dB = 1/(2 x π x RC) = 2kHz R3 = R4/(2-1/Q); with Q = 1, R3 = R4. A Single +1.5 V Supply, Two Op Amp Instrumentation Amplifier The TS1005’s ultra-low supply current and ultra-low voltage operation make it ideal for battery-powered applications such as the instrumentation amplifier shown in Figure 4. The circuit utilizes the classic two op amp instrumentation amplifier topology with four resistors Figure 2: A Simple, Single-pole Active Low-Pass Filter. Figure 3: A Micropower 2-Pole Sallen-Key Low-Pass Filter. Figure 4: A Two Op Amp Instrumentation Amplifier. Figure 1: A Micropower, Precision Oxygen Gas Sensor Amplifier. |
Similar Part No. - TS1005IG5T |
|
Similar Description - TS1005IG5T |
|
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.NET |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
