Electronic Components Datasheet Search |
|
LMH0071 Datasheet(PDF) 4 Page - Texas Instruments |
|
|
LMH0071 Datasheet(HTML) 4 Page - Texas Instruments |
4 / 33 page LMH0041, LMH0051 LMH0071, LMH0341 SNLS272Q – APRIL 2007 – REVISED APRIL 2013 www.ti.com PIN DESCRIPTIONS Pin Name Type Description LVDS Input Interface RX[4:0]+ Output, LVDS LVDS Data Output Pins RX[4:0]- Five channel wide DDR interface. RXCLK+ Output, LVDS LVDS Clock Output Pins RXCLK- DDR Interface. Serial Data Inputs RXIN0+ Input, Differential Serial differential input Pins RXIN0- Channel 0 RXIN1+ Input, Differential Serial differential input Pins RXIN1- Channel 1 Loopthrough Serial Output TXOUT+ Output, CML Serial Digital Interface Output Pin Non-Inverting Output TXOUT- Output, CML Serial Digital Interface Output Pin Inverting Output SMBus Interface SDA I/O, LVCMOS SMBus Data I/O Pin SCK Input, LVCMOS SMBus Clock Input Pin SMB_CS Input, LVCMOS SMBus Chip Select Input Pin Device is selected when High. Control and Configuration Pins RESET Input, LVCMOS Reset Input Pin H = normal mode L = device in RESET LOCK Output, LVCMOS PLL LOCK Status Output H = unlock condition L = PLL is Locked DVB_ASI Input, LVCMOS DVB_ASI Select Input H = DVB_ASI Mode enabled L = Normal Mode enabled Loopthru_EN Input, LVCMOS Loopthrough enable Input H=Reclocked Loopthrogh active L=Reclocked Loopthrough disabled RX_MUX_SEL Input, LVCMOS Input multiplexer select H=RXIN1 selected L=RXIN0selected GPIO[2:0] I/O, LVCMOS General Purpose Input / Output Software configurable I/O pins. RSVD_H Input, LVCMOS Configuration Input – Must tie High Pull High via 5 k Ω resistor to VDD3V3 Analog Inputs RSET Input Serial Loopthrough Output Amplitude Control Resistor connected from this pin to ground to set the signal amplitude. Nominally 7.87k Ω for 800mV output (SMPTE). LF_CP Input Loop Filter Connection LF_REF Loop Filter Reference DNC Do Not Connect – Leave Open Power Supply and Ground VDD3V3 Power 3.3V Power Supply connection VDDPLL Power 3.3V PLL Power Supply connection VDD2V5 Power 2.5V Power Supply connection GND Ground Ground connection – The DAP (large center pad) is the primary GND connection for the device and must be connected to Ground along with the GND pins. 4 Submit Documentation Feedback Copyright © 2007–2013, Texas Instruments Incorporated Product Folder Links: LMH0041 LMH0051 LMH0071 LMH0341 |
Similar Part No. - LMH0071 |
|
Similar Description - LMH0071 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |