Electronic Components Datasheet Search |
|
TMS29F010-90C5FME Datasheet(PDF) 7 Page - Texas Instruments |
|
TMS29F010-90C5FME Datasheet(HTML) 7 Page - Texas Instruments |
7 / 36 page TMS29F010 131072 BY 8BIT FLASH MEMORY SMJS840A − NOVEMBER 1997 − REVISED JUNE 1998 7 POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443 command definitions (continued) Table 3. Command Definitions† COMMAND BUS CYCLES 1ST CYCLE ADDR DATA 2ND CYCLE ADDR DATA 3RD CYCLE ADDR DATA 4TH CYCLE ADDR DATA 5TH CYCLE ADDR DATA 6TH CYCLE ADDR DATA Read‡ 1 RA RD Reset/Read§ 2 XXXXh F0h RA RD Reset/Read§ 4 5555h AAh 2AAAh 55h 5555h F0h RA RD Algorithm selection 4 5555h AAh 2AAAh 55h 5555h 90h RA RD Byte program 4 5555h AAh 2AAAh 55h 5555h A0h PA PD Chip erase 6 5555h AAh 2AAAh 55h 5555h 80h 5555h AAh 2AAAh 55h 5555h 10h Sector erase 6 5555h AAh 2AAAh 55h 5555h 80h 5555h AAh 2AAAh 55h SA 30h RA = Address of the location to be read PA = Address of the location to be programmed SA = Address of the sector to be erased Addresses A14, A15, and A16 select one of eight sectors RD = Data to be read at the selected address location PD = Data to be programmed at the selected address location † Address pins A15 and A16 = VIL or VIH for all bus-cycle addresses except for program address (PA), sector address (SA), and read address (RA). ‡ No command cycles are required when the device is in read mode. § The reset command is required to return to the read mode when the device is in the algorithm-selection mode or if DQ5 goes high. reset/read command The read mode is activated by writing either of the two reset command sequences into the command register. The device remains in this mode until another valid command sequence is input into the command register. Memory data is available in the read mode and can be read with standard microprocessor read-cycle timing. On power up, the device defaults to the read mode; therefore, a reset command sequence is not required and memory data is available. algorithm-selection command The algorithm-selection command allows access to a binary code that matches the device with the proper programming- and erase-command operations. After writing the three-bus-cycle command sequence, the first byte of the algorithm-selection code (01h) can be read from address XX00h. The second byte of the code (20h) can be read from address XX01h (see Table 2). This mode remains in effect until another valid command sequence is written to the device. Sector protection can be determined by using the algorithm-selection command. After issuing the three bus-cycle command sequence, the sector-protection status can be read on DQ0. Set address pins A0 = VIL and A1 = VIH, and then the sector address pins A14, A15, and A16 select the sector to be checked. The remaining address pins can be VIL or VIH. If the sector that is selected is protected, DQ0 outputs a 1 state, and, if the sector selected is not protected, DQ0 outputs a 0 state. This mode remains in effect until another valid command sequence is written to the device. byte-program command Byte programming is a four-bus-cycle command sequence. The first three bus cycles put the device into the program-setup state, and the fourth bus cycle loads the address location and the data to be programmed into the device. The addresses are latched on the falling edge of W and the data is latched on the rising edge of W in the fourth bus cycle. The rising edge of W starts the byte-program operation. The embedded byte-programming function automatically provides needed voltage and timing to program and to verify the cell margin. Any further commands written to the device during the program operation are ignored. |
Similar Part No. - TMS29F010-90C5FME |
|
Similar Description - TMS29F010-90C5FME |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |