Electronic Components Datasheet Search |
|
CDB455C3 Datasheet(PDF) 2 Page - Shoulder Electronics Limited. |
|
CDB455C3 Datasheet(HTML) 2 Page - Shoulder Electronics Limited. |
2 / 3 page 1. Application This specification is applicable to ceramic discriminator CDB455C3 use for communication equipment. 2. Electrical Characteristics This discriminator must need following performance. 2-1) Anti-resonate frequency (Fa) : 455±1.5 kHz. 2-2) Resonant Impedance (Ri): 70 ohms Max. 2-3) ΔF(Fa-Fr) : 48±5.0 kHz. Fr: resonant frequency 2-4) Capacitance (at 1 kHz) : 550 pF±20%. 3. Environmental Test 3-1) Temperature Characteristics At the temperature range of 25±5℃,the discriminators shall meet the electrical properties in item 2-1~2-4,and at –20~+80℃ the Anti-resonant frequency shall not very more than ±2.0 kHz. 3-2) Vibration The discriminators shall suffer no mechanical damage and meet the 2-1~2-4 electrical Characteristics after being vibrated with a sine wave motion having an amplitude of 1.0 mm from 10 to 55KHz per 1 minute, applied for 30 minutes in three different directions (x,y,z). 3-3) Humidity The discriminators shall be place in a humidity chamber at 90~95% relative humidity and 40~45℃ for a period of minimum 8 hours. The discriminators shall be left for the period of more than 24 hours at the room temperature after its removal from the humidity chamber.The discriminators shall meet the 2-1~2-4 electrical characteristics and the appearance of discriminators is to be normal. 3-4) Dropped Shock The discriminators shall suffer no mechanical damage and meet the 2-1~2-4 electrical characteristics outlined on this specification after being dropped 3 times to concrete floor from the 30 cm height. 3-5) Solder ability The terminal surface shall be covered over 3/4 by the solder after dipped the leads into 230±5℃ solder pot containing (Sn 63% Pb 37%) molten alloy for 3±1 seconds. 3-6) Soldering Heat-Resistance The discriminators shall be assembled to the 1 mm “through-hole” P.C. bored and placed in solder solution (Sn63% Pb37%) at 250±10℃ for duration of 3±1 seconds. After removal from the solder solution chamber, the discriminators may be cleaned with chlorothene and left for more then 24 hours at the room temperature. The discriminators shall meet the 2-1~2-4 electrical characteristics are to be normal. 3-7) Lead Strength The discriminators shall suffer no mechanical damage and meet the 2-1~2-4 electrical characteristics outlined on this specification after static load of 1.0 kg for 1 minute is applied in the direction of the insertion side. 3-8) Temperature The discriminators shall be held at each cycle consist of three temperature Http://www.shoulder.cn SHOULDER ELECTRONICS LIMITED Page: 2 |
Similar Part No. - CDB455C3 |
|
Similar Description - CDB455C3 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |