Electronic Components Datasheet Search
  English  ▼
ALLDATASHEET.NET

X  

58246-3 Datasheet(PDF) 2 Page - Tyco Electronics

Part # 58246-3
Description  The head must be installed in Pistol Grip Manual Handle Assembly
Download  6 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  MACOM [Tyco Electronics]
Direct Link  http://www.macom.com
Logo MACOM - Tyco Electronics

58246-3 Datasheet(HTML) 2 Page - Tyco Electronics

  58246-3 Datasheet HTML 1Page - Tyco Electronics 58246-3 Datasheet HTML 2Page - Tyco Electronics 58246-3 Datasheet HTML 3Page - Tyco Electronics 58246-3 Datasheet HTML 4Page - Tyco Electronics 58246-3 Datasheet HTML 5Page - Tyco Electronics 58246-3 Datasheet HTML 6Page - Tyco Electronics  
Zoom Inzoom in Zoom Outzoom out
 2 / 6 page
background image
408-4147
Terminating Head 58246-3
Rev A
2 of 6
Tyco Electronics Corporation
2. Using a small knife, cut off the wire retainers
(strain relief) of the connector. This will provide a
clear view for inspecting the connector for a
properly terminated wire in the contact. See
Figure 3.
Wire retainers are removed in a connector for
testing only. DO NOT use such connectors for
productionapplication.
3. Make a test termination according to Steps 1
through 6 of Section 5, TERMINATING
PROCEDURE.
4. Push the connector out of the right side of the
head.
5. Check that the wire insertion depth is within the
dimension given in Figure 3.
To obtainthe wire insertiondepth, measure from
the front of the contact beam to the center of the
wire as showninFigure3-or- measure from
the front of the contact beam to the back of the
wire and subtract the wire diameter divided by 2.
If it is not, proceed as follows:
For the manual handle assembly, refer to
Section 4, WIRE INSERTION DEPTH
ADJUSTMENT.
For the pneumatic handle assembly, if the wire is
inserted too deeply (more than the required wire
insertion depth), refer to Section 4, WIRE
INSERTION DEPTH ADJUSTMENT. If the wire is
not inserted deeply enough (less than the required
wire insertion depth), increase the air pressure by
69 kPa [10 psi]. Repeat the termination procedure
and check the insertion depth. Continue in this
manner until either the proper insertion depth is
obtained or the air pressure is set to 483 kPa
[70 psi]. If the proper insertion depth is NOT
reached at 483 kPa [70 psi], return the air pressure
to 276 kPa [40 psi], and refer to Section 4.
6. Inspect the termination according to
Paragraph 3.2.
3.2. Termination Inspection (Refer to Figure 3)
Refer to 114-1019 for detailed explanation of the
termination inspection requirements.
1 — The required wire insertion depth is within the
dimension given in Figure 3 (refer to Step 5 of
Paragraph 3.1 for measurement).
2 — The end of the wire extends past the contact
beam by at least 1.52 mm [.060 in.].
Contact (Partially
Removed)
1.52 mm [.060 in.] Min
End of Wire Extends Past
Contact Beam
Wire Retainer
(Strain Relief)
Removed
Lock
(Ramp, Ref)
Test Connector
Production Connector
Wire Extends Past Wire
Retainer (Strain Relief)
Contact Beams
Not Deformed
Termination Inspection
Wire Insulation
Not Nicked or Cut
1
2
3
4
1.88+0.33/-0.13 mm [.074+.013/-.005 in.]
Wire Insertion Depth
(Front of Contact Beam to Center of Wire)
5
Wire
Figure 3
CAUTION
!
NOTE
i
NOTE
i


Similar Part No. - 58246-3

ManufacturerPart #DatasheetDescription
logo
FIBOX Enclosing innovat...
5824000 FIBOX-5824000 Datasheet
79Kb / 2P
   Enclosure, PC
17.01.2023
5824001 FIBOX-5824001 Datasheet
85Kb / 2P
   Enclosure, PC
17.01.2023
5824002 FIBOX-5824002 Datasheet
242Kb / 2P
   Enclosure, ABS
17.01.2023
5824004 FIBOX-5824004 Datasheet
616Kb / 2P
   Enclosure, PC
17.01.2023
5824005 FIBOX-5824005 Datasheet
456Kb / 2P
   Enclosure, PC
17.01.2023
More results

Similar Description - 58246-3

ManufacturerPart #DatasheetDescription
logo
Tyco Electronics
408-4146 MACOM-408-4146 Datasheet
297Kb / 6P
   The head must be installed in Pistol Grip Manual Handle Assembly
logo
TE Connectivity Ltd
408-6789 TEC-408-6789 Datasheet
268Kb / 5P
   Pistol Grip Pneumatic Handle Assembly
logo
Tyco Electronics
411-18339 MACOM-411-18339 Datasheet
2Mb / 11P
   The operating manual must be constantly within reach of the tool.
412-18745 MACOM-412-18745 Datasheet
1Mb / 26P
   The operating manual must be constantly within reach of the tool.
logo
PHOENIX CONTACT
2701276 PHOENIX-2701276 Datasheet
42Kb / 2P
   Cover must be installed if Operator Panel is not used.
logo
Tyco Electronics
408-4109 MACOM-408-4109 Datasheet
547Kb / 5P
   Pistol Grip Seating Tool
logo
TE Connectivity Ltd
409-32041 TEC-409-32041 Datasheet
695Kb / 9P
   12 Ton Pistol Grip
logo
Tyco Electronics
408-10366 MACOM-408-10366 Datasheet
171Kb / 3P
   The Electro--Hydraulic Hand Tool and specific DAHT head assemblies must be ordered separately.
logo
Schneider Electric
VLSH3S7NRD SCHNEIDER-VLSH3S7NRD Datasheet
86Kb / 2P
   Disconnect switch, TeSys VLS, pistol grip handle, 70 mm diameter, screw mounting, red handle, 7 mm shaft, defeatable
VLSH3S7NBD SCHNEIDER-VLSH3S7NBD Datasheet
69Kb / 2P
   Disconnect switch, TeSys VLS, pistol grip handle, 70 mm diameter, screw mounting, black handle, 7 mm shaft, defeatable
More results


Html Pages

1 2 3 4 5 6


Datasheet Download

Go To PDF Page


Link URL




Privacy Policy
ALLDATASHEET.NET
Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com