Electronic Components Datasheet Search |
|
6--22278--5 Datasheet(PDF) 1 Page - Tyco Electronics |
|
6--22278--5 Datasheet(HTML) 1 Page - Tyco Electronics |
1 / 5 page Instruction Sheet Feed- Through Head Assembly 58443- 1 408--9607 LOC B 1 of 5 E 2010 Tyco Electronics Corporation, Berwyn, PA All Rights Reserved TE logo and Tyco Electronics are trademarks. *Trademark. Other products names, logos, or company names might be trademarks of their respective owners. TOOLING ASSISTANCE CENTER 1--800--722--1111 PRODUCT INFORMATION 1--800--522--6752 This controlled document is subject to change. For latest revision and Regional Customer Service, visit our website at www.tycoelectronics.com 20 DEC 10 Rev C For Discrete Wire MTA- 156 Receptacles Figure 1 Rod Inserter Adjuster Locating Pawl Wire Inserter (Hidden) Feed Slide Wire Subassembly Retainer Insert Housing 1. INTRODUCTION Feed--Through Head Assembly 58443--1 is used to terminate discrete wires onto MTA--156 Receptacles 640599--[ ] (for wire size 18 AWG) and Receptacles 640604--[ ] (for wire size 26 AWG) with a maximum insulation diameter of 2.41 mm [.095 in.]. Read these instructions thoroughly before using the head. The head must be mounted onto one of the following tools (for operating procedure for the tool, refer to the instructions packaged with the tool): — Pistol Grip Manual Handle Assembly 58074--1 (408--6790) — Electric Power Unit 931800--1 (409--5746) — Pistol Grip Pneumatic Handle Assembly 58075--1 (408--6789) — Pneumatic Power Bench Assembly 58338--1 (408--9393) All numerical values in this instruction sheet are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters [and inches]. Figures are not drawn to scale. Reasons for reissue of this instruction sheet are provided in Section 8, REVISION SUMMARY. 2. DESCRIPTION The head serves as a guide and support for the receptacle during termination. Features of the head assembly (shown in Figure 1) and functions are as follows: Wire inserter—forces the wire into the two slotted beams of the contact. Note that it provides support for the contact beams when applying insertion force on the wire. Rod inserter adjuster—is a piston for the wire inserter and regulates wire inserter travel. Feed slide—automatically positions the receptacle after each termination. Locating pawl—aligns the receptacle for insertion, and retains it during termination. The locating pawl is sometimes referred to as the “anti--backup pawl.” Insert housing—holds the receptacle in place in relation to the wires. Wire subassembly retainer—holds the wires in place in relation to the receptacle. 3. TEST CRIMP AND HEAD ADJUSTMENTS 3.1. Test Crimp 1. Make a termination according to Section 4, Steps 1 through 6. If the receptacle cannot be inserted into the head, or if the receptacle is too loose in the head, adjust the insert housing according to Paragraph 3.2. NOTE i |
Similar Part No. - 6--22278--5 |
|
Similar Description - 6--22278--5 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.NET |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |