 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
DS1699S-100 Datasheet(PDF) 2 Page - Dallas Semiconductor |
|
||||||||||||||||||||||||||||||
DS1699S-100 Datasheet(HTML) 2 Page - Dallas Semiconductor |
|
|
2 / 10 page  DS1668, DS1669, DS1669S 081895 2/10 DESCRIPTION The DS1668 and DS1669 Dallastats are digital rheo- stats or potentiometers. These units provide 64 pos- sible uniform tap points over the resistive range and are available in standard versions of 10K, 50K, and 100K ohms. The Dallastats can be controlled by either a mechanical–type contact closure input or a digital source input such as a CPU. Wiper position is main- tained in the absence of power which is accomplished through the use of a EEPROM memory cell array. The EEPROM cell array is specified to accept greater than 80,000 writes. The DS1668 and DS1669 differ in the type packages in which they are offered. The DS1668 is only available in a custom 6–pin package with a single integrated push- button as shown in the package drawing. The single integrated pushbutton provides the mechanical control input of the wiper position. In addition, a digital source input, D, allows the potentiometer to be controlled by a microcontroller or processor. Other package pins include the positive voltage input, +V, the negative volt- age input, –V, the resistor wiper terminal, RW, and the high resistor terminal, RH. The DS1668 is rated for com- mercial temperature usage only (0 °C to 70°C). The DS1669 is offered in two standard IC packages which include an 8–pin 300 mil DIP and an 8–pin 200 mil SOIC. Like the DS1668, the DS1669 can be configured to operate using a single pushbutton or digital source input. This is illustrated in Figure 1. Additionally, the DS1669 can be configured to operate in a dual pushbut- ton configuration which is shown in Figure 2. The DS1669 pinouts allow access to both ends of the poten- tiometer RL, RH, and the wiper, RW. Control inputs include the digital source input, D, the up contact input, UC, and the down contact input, DC. Other package pinouts include the positive,+V, and negative, –V , sup- ply inputs. The DS1669 is available in commercial or industrial temperature versions. OPERATION The DS1668/DS1669 Dallastats are controlled through a contact closure input or by a digital source input. The DS1668 is configured to operate from a single contact closure (pushbutton) input which is integrated in the custom 6–pin package or the device can be driven from the digital source input (D). The DS1669 can be con- trolled using a single pushbutton input, dual pushbutton, or using the digital source input. Figure 3 illustrates the single pushbutton configuration of the DS1668. Internally, the low end resistor terminal is connected to the negative supply input terminal. The integrated pushbutton has one side connected to the negative supply input while the other side is connected to the up contact terminal (UC). The digital source input (D) is accessible through pin 4 of the package. The (D) input has an internal pull–up resistor and can be allowed to float when not in use. The down contact input (DC) is not accessible externally. However, this control input is internally connected to the positive input supply. When powered, the DS1668 assumes a single pushbut- ton mode of operation. Pressure applied to the inte- grated pushbutton will cause contact closure which in turn will move the wiper position upward or downward depending on the previous wiper direction. Single push- button mode is accomplished in the same manner for the DS1669. However, for the DS1669, all connections must be made by the user since no internal connections exist (see Figure 1). Note that single pushbutton control is accomplished when 1) the (DC) input is connected to the positive supply input and 2) the (D) input is allowed to float. These two conditions must exist from the time of device power–up. The UC input controls both upward and downward movement of the device wiper position in single pushbutton mode of operation. Dual pushbutton operation is only available when using the DS1669. The DS1668, by design, only supports the single pushbutton mode of operation and digital source input control. Figure 2 provides a typical application example of the dual pushbutton configuration for the DS1669. In dual–pushbutton mode, the up–contact input (UC) is used solely to provide upward movement of the wiper position and the down–contact input (DC) is used to provide downward movement of the wiper posi- tion. For dual pushbutton configuration, all control inputs (UC, DC, and D) must remain open on device power–up. The digital source input, D, was designed for micropro- cessor or controller applications. This control input manipulates the device in the same manner as the single pushbutton configuration; controlling movement of the wiper position in both upward and downward directions. One added feature over the single pushbut- ton configuration is the ability to increment or decrement wiper position at a faster rate. Digital source input con- trol is available regardless of the type of pushbutton configuration. |
Similar Part No. - DS1699S-100 |
|
Similar Description - DS1699S-100 |
|
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.NET |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
