 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
ST10F273Z4 Datasheet(PDF) 20 Page - STMicroelectronics |
|
||||||||||||||||||||||||||||||
ST10F273Z4 Datasheet(HTML) 20 Page - STMicroelectronics |
|
|
20 / 188 page  Pin data ST10F273Z4 20/188 XTAL1 138 I XTAL1 Main oscillator amplifier circuit and/or external clock input. XTAL2 137 O XTAL2 Main oscillator amplifier circuit output. To clock the device from an external source, drive XTAL1 while leaving XTAL2 unconnected. Minimum and maximum high / low and rise / fall times specified in the AC Characteristics must be observed. XTAL3 143 I XTAL3 32 kHz oscillator amplifier circuit input XTAL4 144 O XTAL4 32 kHz oscillator amplifier circuit output When 32 kHz oscillator amplifier is not used, to avoid spurious consumption, XTAL3 shall be tied to ground while XTAL4 shall be left open. Besides, bit OFF32 in RTCCON register shall be set. 32 kHz oscillator can only be driven by an external crystal, and not by a different clock source. RSTIN 140 I Reset Input with CMOS Schmitt-Trigger characteristics. A low level at this pin for a specified duration while the oscillator is running resets the ST10F273Z4. An internal pull-up resistor permits power-on reset using only a capacitor connected to VSS. In bidirectional reset mode (enabled by setting bit BDRSTEN in SYSCON register), the RSTIN line is pulled low for the duration of the internal reset sequence. RSTOUT 141 O Internal Reset Indication Output. This pin is driven to a low level during hardware, software or watchdog timer reset. RSTOUT remains low until the EINIT (end of initialization) instruction is executed. NMI 142 I Non-Maskable Interrupt Input. A high to low transition at this pin causes the CPU to vector to the NMI trap routine. If bit PWDCFG = ‘0’ in SYSCON register, when the PWRDN (power down) instruction is executed, the NMI pin must be low in order to force the ST10F273Z4 to go into power down mode. If NMI is high and PWDCFG =’0’, when PWRDN is executed, the part will continue to run in normal mode. If not used, pin NMI should be pulled high externally. VAREF 37 - A/D converter reference voltage and analog supply VAGND 38 - A/D converter reference and analog ground RPD 84 - Timing pin for the return from interruptible power down mode and synchronous / asynchronous reset selection. VDD 17, 46, 72,82,93, 109, 126, 136 - Digital supply voltage = + 5V during normal operation, idle and power down modes. It can be turned off when Stand-by RAM mode is selected. VSS 18,45, 55,71, 83,94, 110, 127, 139 - Digital ground V18 56 - 1.8V decoupling pin: a decoupling capacitor (typical value of 10nF, max 100nF) must be connected between this pin and nearest VSS pin. Table 2. Pin description (continued) Symbol Pin Type Function |
Similar Part No. - ST10F273Z4 |
|
Similar Description - ST10F273Z4 |
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.NET |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
allmanual.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
