194D

www.vishay.com

Vishay Sprague

Revision: 21-Jun-17

1

Document Number: 40000

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

Solid Tantalum Chip Capacitors,

PERFORMANCE CHARACTERISTICS

www.vishay.com/doc?40194

Operating Temperature: -55 °C to +125 °C

(above 85 °C, voltage derating is required)

Capacitance Range: 0.10 μF to 330 μF

Capacitance Tolerance: ± 10 %, ± 20 % standard

FEATURES

• 8 mm, 12 mm, 16 mm tape and reel packaging

available

per

EIA-481

and

reeling

per

IEC 60286-3, 7" [178 mm] standard

• Mounting: surface mount

• Material categorization: for definitions of compliance

Note

RoHS-compliant and / or parts that are non RoHS-compliant. For

example, parts with lead (Pb) terminations are not RoHS-compliant.

Please see the information / tables in this datasheet for details

Note

• Preferred tolerance and reel sizes are in bold.

We reserve the right to supply higher voltage ratings and tighter capacitance tolerance capacitors in the same case size

Note

• When solder coated terminations are required, add 0.015" [0.381 mm] to termination dimension tolerances

Available

Available

ORDERING INFORMATION

194D

225

X0

004

A

2

T

TYPE

CAPACITANCE

CAPACITANCE

TOLERANCE

DC VOLTAGE RATING

AT +85 °C

CASE CODE

TERMINATION

PACKAGING

This is expressed

in picofarads. The

first two digits are

the significant

figures. The third

is the number of

zeros to follow.

X0 = ± 20 %

X9 = ± 10 %

X5 = ± 5 %

Special order

This is expressed in volts.

To complete the

three-digit block, zeros

precede the voltage rating

See Ratings

and Case

Codes table

2 = gold plated

(50 μ inch minimum)

standard

(RoHS compliant)

8 = 60/40 solder plated

6 = 60/40 solder plated,

fused

7 = hot solder dipped

T = T/R (full reel)

7" [178 mm] reel

standard

H = T/R (half reel)

7" [178 mm]

U = T/R (partial reel)

7" [178 mm]

B = bulk

DIMENSIONS in inches [millimeters]

CASE CODE

W

L

H

P

A

0.050 ± 0.015

[1.27 ± 0.38]

0.100 ± 0.015

[2.54 ± 0.38]

0.050 ± 0.015

[1.27 ± 0.38]

0.030 ± 0.005

[0.76 ± 0.13]

0.005

[0.13]

0.015

[0.38]

B

0.050 ± 0.015

[1.27 ± 0.38]

0.150 ± 0.015

[3.81 ± 0.38]

0.050 ± 0.015

[1.27 ± 0.38]

0.030 ± 0.005

[0.76 ± 0.13]

0.005

[0.13]

0.015

[0.38]

C

0.050 ± 0.015

[1.27 ± 0.38]

0.200 ± 0.015

[5.08 ± 0.38]

0.050 ± 0.015

[1.27 ± 0.38]

0.030 ± 0.005

[0.76 ± 0.13]

0.005

[0.13]

0.015

[0.38]

D

0.100 ± 0.015

[2.54 ± 0.38]

0.150 ± 0.015

[3.81 ± 0.38]

0.050 ± 0.015

[1.27 ± 0.38]

0.030 ± 0.005

[0.76 ± 0.13]

0.005

[0.13]

0.015

[0.38]

E

0.100 ± 0.015

[2.54 ± 0.38]

0.200 ± 0.015

[5.08 ± 0.38]

0.050 ± 0.015

[1.27 ± 0.38]

0.030 ± 0.005

[0.76 ± 0.13]

0.005

[0.13]

0.015

[0.38]

F

0.135 ± 0.015

[3.43 ± 0.38]

0.220 ± 0.015

[5.59 ± 0.38]

0.070 ± 0.015

[1.78 ± 0.38]

0.030 ± 0.005

[0.76 ± 0.13]

0.005

[0.13]

0.015

[0.38]

G

0.110 ± 0.015

[2.79 ± 0.38]

0.265 ± 0.015

[6.73 ± 0.38]

0.110 ± 0.015

[2.79 ± 0.38]

0.050 ± 0.005

[1.27 ± 0.13]

0.005

[0.13]

0.015

[0.38]

H

0.150 ± 0.015

[3.81 ± 0.38]

0.285 ± 0.015

[7.24 ± 0.38]

0.110 ± 0.015

[2.79 ± 0.38]

0.050 ± 0.005

[1.27 ± 0.13]

0.005

[0.13]

0.015

[0.38]

W

L

T

P

H

P

T

Weld and

dimple

projection

identifies

anode (+)

terminal